Advertising:

Fuel Injector Deadtimes: Difference between revisions

From MS4X Wiki
Line 93: Line 93:


=Bosch=
=Bosch=
== Bosch 0280150945 312cc Red-tops (Ford  F1SE-E5A) ==
===Bosch 0280150945===
[[File:0280150945.JPG|250px|thumb|right|Bosch 0280150945 Injector]]
[[File:0280150945.JPG|250px|thumb|right|Bosch 0280150945 Injector]]


312cc Red-tops (Ford  F1SE-E5A)
Flow rate: 337cm³/min @ 3.5 bar
Flow rate: 337cm³/min @ 3.5 bar



Revision as of 15:03, 4 May 2021

Every fuel injector type has a unique minimum injection time and latency for it to fully open once energized.

This latency is often referred to as injector lag, dead time, offset, or delay (ip_ti_add_dly__vb).

It is strongly dependent on the supply voltage and therefore stored in an interpolated table.

The minimum injection time is also important to make sure the injection pattern is clear and complete. (c_ti_min_iv). Minimum injection time is calculated by subtracting the dead time at 14v from the minimum pulse width.

All values here are meant for the standard fuel pressure of 3.5 bars (50.76 psi). The flow rate for different pressures can be calculated here: Injector Calculator

The voltage describing Y-axis ldpm_vb_1 is also used for the ignition coil charging Dwell time tables ip_td_*. Be careful with changes to the axis values!

ATTENTION: The conversion factor of the old definitions files is wrong. Correct conversion factor for injector deadtime is "X * 0.032", resulting in a range of 0.00ms to 8.16ms.

Hint: In order to work with an unmodified, factory fuel injector harness on M5X engine cars, the injectors used must have an EV1/Jetronic (square/rectangular) connector. Injectors with an EV6/EV14/USCAR (oval) connector will require adapters.

BMW OEM

BMW M52TU OEM injectors

Siemens part number: A2C59511971 / 1427240

Flow rate: 225cm³/min @ 3.5 bar

Minimum injection time M52TUB20: 0.640ms

Minimum injection time M52TUB23/28: 0.624ms

kf_ti_add_totz__ub
V ms
0.0 3.65
6.0 3.65
8.0 1.84
10.0 1.23
12.0 0.81
14.0 0.55
16.0 0.39
25.0 0.06

BMW M54B30 OEM injectors

Siemens part number: A2C59514053 / 1439800

Flow rate: 252cm³/min @ 3.5 bar

Minimum injection time: 0.725ms

ip_ti_add_dly__vb
V ms
0.0 3.328
6.0 3.328
8.0 1.408
10.0 0.864
12.0 0.576
14.0 0.384
16.0 0.256
25.0 0.032

Bosch

Bosch 0280150945

Bosch 0280150945 Injector

312cc Red-tops (Ford F1SE-E5A) Flow rate: 337cm³/min @ 3.5 bar

Minimum injection time: 0.496ms

ip_ti_add_dly__vb
V ms
0.0 3.33
6.0 3.33
8.0 1.41
10.0 0.86
12.0 0.58
14.0 0.38
16.0 0.26
25.0 0.03

Bosch 0280158227 375cc (Ford BR3E-E5A)

These will require an EV1 to EV6/EV14 adapter to use them with an M5X fuel injector harness.

Flow rate: 435cm³/min @ 3.5 bar

Minimum injection time: 0.460ms

ip_ti_add_dly__vb
V ms
0.0 4.91
6.0 4.91
8.0 2.35
10.0 1.62
12.0 1.19
14.0 0.94
16.0 0.85
25.0 0.85

These are OE injectors for the 2011-2015 Ford Mustang 5.0. (Ford part # BR3E-E5A)

Bosch 0280155968 440cc Green Giants

Bosch 0280155968 Injector

Flow rate: 466cm³/min @ 3.5 bar

Minimum injection time: 0.468ms

ip_ti_add_dly__vb @ 3 bar
V ms
0.0 4.986
6.0 4.986
8.0 2.098
10.0 1.321
12.0 0.919
14.0 0.670
16.0 0.47
25.0 0.47
ip_ti_add_dly__vb @ 3.5 bar
V ms
0.0 5.216
6.0 5.216
8.0 2.208
10.0 1.376
12.0 0.960
14.0 0.704
16.0 0.480
25.0 0.480

(Same values apply to Bosch 280150558 green-tops (Ford Part# M-9593-F302)


Bosch 0280158123 627cc (Porsche 997 605 132 02)

Bosch 0280158123 Injector
Bosch 0280158123 base map with FPR connected to manifold

Flow rate: 677cm³/min @ 3.5 bar

Minimum injection time: 0.448ms

ip_ti_add_dly__vb
V ms
0.0 3.072
6.0 3.072
8.0 3.072
10.0 1.408
12.0 0.992
14.0 0.768
16.0 0.576
25.0 0.576


If you encounter odd fueling issues, try using the following info instead.

Minimum injection time: 0.160ms

ip_ti_add_dly__vb
V ms
0.0 3.330
6.0 3.330
8.0 2.020
10.0 1.250
12.0 0.860
14.0 0.540
16.0 0.350
25.0 0.030


Lucas/Delphi 42.5 lb/hr 445cc

Part number: 01D030B

Minimum injection time: 0.410ms

ip_ti_add_dly__vb
V ms
0.0 4.35
6.0 4.35
8.0 1.82
10.0 1.12
12.0 0.77
14.0 0.58
16.0 0.51
25.0 0.10

Siemens DEKA 6900371 440cc/min 42lb/hr (Volvo 1.9l turbo)

Flow rate: 440cc/min @ 3 bar

475cc/min @ 3.5 bar


Minimum injection time: 0.501ms

ip_ti_add_dly__vb
V ms
0.0 4.44
6.0 4.44
8.0 1.88
10.0 1.15
12.0 0.94
14.0 0.85
16.0 0.77
25.0 0.04

Siemens DEKA FI114961 (107961) 630cc/min

39.15 PSI/270 kPa:

Minimum injection time: 0.981ms

ip_ti_add_dly__vb
V ms
0.0 2.60
6.0 2.60
8.0 1.45
10.0 0.94
12.0 0.64
14.0 0.43
16.0 0.26
25.0 0.26

Siemens DEKA FI114991 (110324) 875cc/min 80lb/hr

http://www.siemensdeka.com/product/80lbh-siemens-deka-4-mototron-high-impedance-long-style-uscar-fi114991/

43.5PSI / 300kPa:

Minimum injection time: 0.600ms

ip_ti_add_dly__vb
V ms
0.0 2.811
6.0 2.811
8.0 1.777
10.0 1.288
12.0 1.017
14.0 0.801
16.0 0.639
25.0 0.639
  • Ford M-9593-LU80 injectors likely have the same dead time values, but have an EV6/EV14/USCAR connector.

Injector Dynamics ID1050X 1065cc/min (101 lb/hr)

  • These will require an EV1 to EV6/EV14 adapter to use them with an M5X fuel injector harness.

Flow rate: 1235cm³/min @ 3.5 bar

Minimum injection time: 0.200ms

ip_ti_add_dly__vb
V ms
0.0 2.025
6.0 2.025
8.0 2.025
10.0 1.475
12.0 1.160
14.0 0.955
16.0 0.825
25.0 0.825