Advertising:

Siemens MS43 CAN Bus: Difference between revisions

From MS4X Wiki
No edit summary
(38 intermediate revisions by the same user not shown)
Line 5: Line 5:


The messages are ordered by the CAN registers name inside the CPU beginning with 1 and ending with F. Unused boxes are not listed here.
The messages are ordered by the CAN registers name inside the CPU beginning with 1 and ending with F. Unused boxes are not listed here.


Siemens MS43 reads the following messages for operation, if the corresponding module is present in car:
Siemens MS43 reads the following messages for operation, if the corresponding module is present in car:
*Messagebox 1: [[CAN_Bus_ID_0x43F_EGS1|ARBID 0x43F EGS1 Automatic Transmission]]
*Messagebox 1: [[CAN_Bus_ID_0x43F_EGS1|ARBID 0x43F EGS1 Automatic Transmission]]
*Messagebox 2: [[CAN_Bus_ID_0x613_ICL2|ARBID 0x613 ICL2 Instrument Cluster]]
*Messagebox 2: [[CAN_Bus_ID_0x613_ICL2|ARBID 0x613 ICL2 Instrument Cluster]]
Line 13: Line 13:
*Messagebox 4: [[CAN_Bus_ID_0x153_ASC1|ARBID 0x153 ASC1 Traction Control]]
*Messagebox 4: [[CAN_Bus_ID_0x153_ASC1|ARBID 0x153 ASC1 Traction Control]]
*Messagebox 5: [[CAN_Bus_ID_0x1F3_ASC3|ARBID 0x1F3 ASC3 Traction Control]]
*Messagebox 5: [[CAN_Bus_ID_0x1F3_ASC3|ARBID 0x1F3 ASC3 Traction Control]]
*Messagebox 6: [[CAN_Bus_ID_0x153_AMT1|ARBID 0x43D AMT1 Automatic Manual Transmission]]
*Messagebox 6: [[CAN_Bus_ID_0x43D_AMT1|ARBID 0x43D AMT1 Automatic Manual Transmission]]
*Messagebox 7: [[CAN_Bus_ID_0x1F5_LWS1|ARBID 0x1F5 LWS1 Steering Angle Sensor]]
*Messagebox 7: [[CAN_Bus_ID_0x1F5_LWS1|ARBID 0x1F5 LWS1 Steering Angle Sensor]]




=Engine=
Siemens MS43 sends the following messages:
==DME1 0x316==
*Messagebox B: [[Siemens_MS43_CAN_Bus#DME3_0x338|ARBID 0x338 DME3 Engine Control Unit]] (Alpina Roadster only)
*Messagebox C: [[Siemens_MS43_CAN_Bus#DME4_0x545|ARBID 0x545 DME4 Engine Control Unit]]
*Messagebox D: [[Siemens_MS43_CAN_Bus#DME2_0x329|ARBID 0x329 DME2 Engine Control Unit]]
*Messagebox E: [[Siemens_MS43_CAN_Bus#DME1_0x316|ARBID 0x316 DME1 Engine Control Unit]]
 
 
Visualised in Tuner Pro the CAN configuration table looks like this:
[[File:Tuner Pro MS43 CAN Init.png|none]]
 
 
In addition to that, there are several messages that are not used by the ECU, but still present on the CAN Bus:
*[[CAN_Bus_ID_0x1F0_ASC2|ARBID 0x1F0 ASC2 Traction Control]]
*[[CAN_Bus_ID_0x1F8_ASC4|ARBID 0x1F8 ASC4 Traction Control]]
*[[CAN_Bus_ID_0x610_ICL1|ARBID 0x610 ICL1 Instrument Cluster]]
 
 
====DME1 0x316====
Refresh Rate: 10ms
Refresh Rate: 10ms


Line 66: Line 82:
**'''Bit 1 - ERR_AMT_CAN'''
**'''Bit 1 - ERR_AMT_CAN'''


==DME2 0x329==
 
====DME2 0x329====
Refresh Rate: 10ms
Refresh Rate: 10ms


Line 76: Line 93:
**'''Bit 4''' - MUX_INFO [4]
**'''Bit 4''' - MUX_INFO [4]
**'''Bit 5''' - MUX_INFO [5]
**'''Bit 5''' - MUX_INFO [5]
**: CAN_LEVEL = CAN bus function level. This is always 0x11 for MS43
**: OBD_STEUER = STATE_DIAG_GS (Status of GS diagnosis for feedback to gearbox)
**: MD_NORM = Refactored C_TQ_STND from 0x3FF (0-1023Nm) to 0x3F (0-1008Nm) with decreased resolution of 16Nm
**: MD_NORM = Refactored C_TQ_STND from 0x3FF (0-1023Nm) to 0x3F (0-1008Nm) with decreased resolution of 16Nm
**'''Bit 6''' - MUX_CODE [0]
**'''Bit 6''' - MUX_CODE [0]
Line 157: Line 176:
*'''Byte 7 - Unused'''
*'''Byte 7 - Unused'''


==DME4 0x545==
 
====DME3 0x338====
Refresh Rate: 1000ms and at signal change
 
*'''Byte 0''' - Unused
*'''Byte 1''' - Unused
*'''Byte 2 - STATE_SOF_CAN'''
*:Sport Button Status
*:0 = Sport Button On (requested by SMG)
*:1 = Sport Button Off
*:2 = Sport Button On
*:3 = Sport Button Error
*:Init: 0x01
*'''Byte 3''' - Unused
*'''Byte 4''' - Unused
*'''Byte 5''' - Unused
*'''Byte 6''' - Unused
*'''Byte 7''' - Unused
 
====DME4 0x545====
Refresh Rate: 10ms
Refresh Rate: 10ms


*'''Byte 0 - Bitfield'''
*'''Byte 0 - Bitfield'''
**'''Bit 0''' - DDE: Pre-Glow Active
**'''Bit 0''' - Unused
**'''Bit 1''' - LV_MIL - Check Engine Light
**'''Bit 1''' - LV_MIL - Check Engine Light
**'''Bit 2''' - Unused
**'''Bit 2''' - Unused
**'''Bit 3''' - LV_MAIN_SWI_CRU - CRU_MAIN_SWI
**'''Bit 3''' - LV_MAIN_SWI_CRU - CRU_MAIN_SWI
**'''Bit 4''' - LV_ETC_DIAG - EML Light
**'''Bit 4''' - LV_ETC_DIAG - EML Light
**'''Bit 5''' - DDE: Boost Control Failure
**'''Bit 5''' - Unused
**'''Bit 6''' - LV_FUC_CAN - Fuel Tank Cap Light
**'''Bit 6''' - LV_FUC_CAN - Fuel Tank Cap Light
**'''Bit 7''' - DDE: Battery Count
**'''Bit 7''' - Unused
*'''Byte 1''' - FCO - Fuel Consumption LSB
*'''Byte 1 - FCO[LSB]'''
*'''Byte 2''' - FCO - Fuel Consumption MSB
*'''Byte 2 - FCO[MSB]'''
*:Fuel Consumption
*'''Byte 3 - Bitfield'''
*'''Byte 3 - Bitfield'''
**'''Bit 0''' - Oil Level Error LED M5 Cluster
**'''Bit 0''' - Oil Level Error LED M5 Cluster
Line 179: Line 218:
**'''Bit 5''' - M-Cluster Warm-Up LEDs
**'''Bit 5''' - M-Cluster Warm-Up LEDs
**'''Bit 6''' - M-Cluster Warm-Up LEDs
**'''Bit 6''' - M-Cluster Warm-Up LEDs
**'''Bit 7''' - DDE: Gear Change Request
**'''Bit 7''' - Unused
*'''Byte 4''' - TOIL_CAN - Oil Temperature
*'''Byte 4 - TOIL_CAN'''
*'''Byte 5''' -
*:Oil Temperature
*'''Byte 6''' - MSS54HP: Oil Level
*'''Byte 7''' - Unused
 
=Automatic Transmission=
==SSG1 0x43D==
Refresh Rate: 10ms
 
*'''Byte 0 - Bitfield'''
**'''Bit 0''' - GEAR_INFO - Active Gear
**'''Bit 1''' - GEAR_INFO - Active Gear
**'''Bit 2''' - GEAR_INFO - Active Gear
**'''Bit 3''' - LV_GS - Gear Shift Active
**'''Bit 4''' - STATE_AMT - Status Shift Process
**'''Bit 5''' - STATE_AMT - Status Shift Process
**'''Bit 6''' -
**'''Bit 7''' - LV_AMT_ES - Engine Stop Request From SMG TCU
*'''Byte 1 - Bitfield'''
**'''Bit 0''' - GEAR_SEL_DISP
**'''Bit 1''' - GEAR_SEL_DISP
**'''Bit 2''' - GEAR_SEL_DISP
**'''Bit 3''' - GEAR_SEL_DISP
**'''Bit 4''' - STATE_AMT_OBD
**'''Bit 5''' - STATE_AMT_OBD
**'''Bit 6''' - STATE_AMT_OBD
**'''Bit 7''' - STATE_AMT_OBD
*'''Byte 2 - Bitfield'''
**'''Bit 0''' -
**'''Bit 1''' -
**'''Bit 2''' -
**'''Bit 3''' - LV_CITY
**'''Bit 4''' -
**'''Bit 5''' - LV_HPA
**'''Bit 6''' - bitfield_FD20_20
**'''Bit 7''' -
*'''Byte 3''' - TQI_AMT_CAN
*'''Byte 4''' - TQI_MAF_AMT_CAN
*'''Byte 5 - Bitfield'''
*'''Byte 5 - Bitfield'''
**'''Bit 0''' - LV_GP - Gearbox Protection
**'''Bit 0''' - Battery Chargelight (Alpina Roadster Only)
**'''Bit 1''' -
**'''Bit 1''' - Unused
**'''Bit 2''' - CTR_AMT - Message Counter For AMT TQI Request
**'''Bit 3''' - CTR_AMT - Message Counter For AMT TQI Request
**'''Bit 4''' - CTR_AMT - Message Counter For AMT TQI Request
**'''Bit 5''' - CTR_AMT - Message Counter For AMT TQI Request
**'''Bit 6''' - STATE_CLU_AMT - State SMG Clutch
**'''Bit 7''' - STATE_CLU_AMT - State SMG Clutch
*'''Byte 6''' - TQI_AMT_CPL_CAN
*'''Byte 7''' - N_MAX_AMT_CAN - Engine Speed Limiter Override During Gearshift
 
==EGS1 0x43F==
Refresh Rate: 10ms
 
*'''Byte 0 - Bitfield'''
**'''Bit 0''' - GEAR_INFO [0]
**'''Bit 1''' - GEAR_INFO [1]
**'''Bit 2''' - GEAR_INFO [2]
**:Current Active Gear
**'''Bit 3''' - LV_GS - Gear Shift Active
**'''Bit 4''' - OBD_F - OBD-relevant DTC Active
**'''Bit 5''' - LV_GP_CAN - Gearbox Protection
**'''Bit 6''' - S_KUPPL / STATE_CC - State Converter Clutch
**'''Bit 7''' - S_KUPPL / STATE_CC - State Converter Clutch
*'''Byte 1 - Bitfield'''
**'''Bit 0''' - GEAR_SEL_DISP [0]
**'''Bit 1''' - GEAR_SEL_DISP [1]
**'''Bit 2''' - GEAR_SEL_DISP [2]
**'''Bit 3''' - GEAR_SEL_DISP [3]
**:Positionswählhebelanzeige
**'''Bit 4''' - STATE_ETCU_OBD [0]
**'''Bit 5''' - STATE_ETCU_OBD [1]
**'''Bit 6''' - STATE_ETCU_OBD [2]
**'''Bit 7''' - STATE_ETCU_OBD [3]
**:OBD-Status Transmission Control Unit
*'''Byte 2 - Bitfield'''
**'''Bit 0''' - SMG_WHL_ANZ - SMG-Wählhebelstellung
**'''Bit 1''' - SMG_WHL_ANZ - SMG-Wählhebelstellung
**'''Bit 2''' - Unused
**'''Bit 2''' - Unused
**'''Bit 3''' - Unused
**'''Bit 3''' - Unused
**'''Bit 4''' - Unused
**'''Bit 4''' - Unused
**'''Bit 5''' - PRG_INF_ANZ - Programminformationsanzeige
**'''Bit 6''' - PRG_INF_ANZ - Programminformationsanzeige
**'''Bit 7''' - PRG_INF_ANZ - Programminformationsanzeige
*'''Byte 3''' - TQI_ETCU_CAN - Momenteneingriff der GS bezogen auf das indizierte Motormoment
*'''Byte 4''' - N_ABTR - Abtriebsdrehzahl
*'''Byte 5 - Bitfield'''
**'''Bit 0''' - L_GS - Störanzeige
**'''Bit 1''' - L_GS - Störanzeige
**'''Bit 2''' - TCU_TYP - Steuergerätetyp EGS/SMG
**'''Bit 3''' - S_EGW - Schalter Getriebeölthermostat
**'''Bit 4''' - LV_TOIL_GEAR_CAN - Schalter Getriebeölübertemperatur
**'''Bit 5''' - Unused
**'''Bit 5''' - Unused
**'''Bit 6''' - DT_REINF - Drivetrain Reinforcement
**'''Bit 7''' - DT_REINF - Drivetrain Reinforcement
*'''Byte 6''' - DT_REINF - Drivetrain Reinforcement
*'''Byte 7''' - TQ_CONV_CAN - Momentaufnahme Getriebe
==SMG2 0x43F==
The SMG2 CAN message for the E46 chassis CAN is sent from the MSS54 ECU instead of the TCU.
MSS54 has a secondary CAN bus that is completely seperated from the rest of the powertrain and acts as a gateway for the SMG2 unit.
Refresh Rate: 10ms
*'''Byte 0 - Bitfield'''
**'''Bit 0 - DESIRED_GEAR [0]'''
**'''Bit 1 - DESIRED_GEAR [1]'''
**'''Bit 2 - DESIRED_GEAR [2]'''
**: Desired Gear After Shift
**: 0 = Neutral
**: 1 = 1st Gear
**: 2 = 2nd Gear
**: 3 = 3rd Gear
**: 4 = 4th Gear
**: 5 = 5th Gear
**: 6 = 6th Gear
**: 7 = Reverse
**'''Bit 3 - LV_GS'''
**: Gear Shift Active
**: 0 = no
**: 1 = yes
**'''Bit 4 - Unused'''
**'''Bit 5 - GEAR_SEL_AUTO'''
**: Gear Selector Auto Position
**: 0 = no
**: 1 = yes
**'''Bit 6 - STATE_CLUTCH [0]'''
**'''Bit 7 - STATE_CLUTCH [1]'''
**: State Converter Clutch
**: 0 = opened
**: 1 = closed
**: 2 = opening
**: 3 = closing
*'''Byte 1 - Bitfield'''
**'''Bit 0 - GEAR_INFO [0]'''
**'''Bit 1 - GEAR_INFO [1]'''
**'''Bit 2 - GEAR_INFO [2]'''
**'''Bit 3 - GEAR_INFO [3]'''
**: Current Gear Display Information
**: 0 = Clear Screen
**: 1 = 1st Gear
**: 2 = 2nd Gear
**: 3 = 3rd Gear
**: 4 = 4th Gear
**: 5 = Auto / D
**: 6 = Neutral
**: 7 = Reverse
**: 9 = 5th Gear
**: 10 = 6th Gear
**'''Bit 4 - Unused'''
**'''Bit 5 - Unused'''
**'''Bit 6 - Unused'''
**'''Bit 7 - Unused'''
*'''Byte 2 - Bitfield'''
**'''Bit 0''' - GEAL_SEL [0]
**'''Bit 1''' - GEAL_SEL [1]
**'''Bit 2''' - GEAL_SEL [2]
**'''Bit 3''' - GEAL_SEL [3]
**:Gear Selector Indicator
**:0 = Display Off
**:1 = "0"
**:2 = "R"
**:3 = "A+"
**:4 = "A-"
**:5 = "A+/-"
**:6 = "S+"
**:7 = "S+"
**:8 = "S+/-"
**:9 = "+"
**:10 = "-"
**:11 = "+/-"
**:12 = "A"
**:15 = Display Segment Test
**'''Bit 4''' - PRG_INF_ANZ [0]
**'''Bit 5''' - PRG_INF_ANZ [1]
**'''Bit 6''' - PRG_INF_ANZ [2]
**'''Bit 7''' - PRG_INF_ANZ [3]
**:Drive Logic Speed Indicator
**:0 = Drive Logic Indicator Hidden
**:1 = DSC Off Frame Extension Only
**:2 = Standard Frame and Speed 1
**:3 = Extended Frame and Speed 1
**:4 = Standard Frame and Speed 2
**:5 = Extended Frame and Speed 2
**:6 = Standard Frame and Speed 3
**:7 = Extended Frame and Speed 3
**:8 = Standard Frame and Speed 4
**:9 = Extended Frame and Speed 4
**:10 = Standard Frame and Speed 5
**:11 = Extended Frame and Speed 5
**:12 = Standard Frame and Speed 6
**:13 = Extended Frame and Speed 6
**:14 = unused
**:15 = unused
*'''Byte 3 - CHKSM_GEAR_INFO'''
*: Checksum and life counter for current gear shown in cluster display
*: There is a COUNTER with an initialization value of 0x00
*:: Calculation:
*:: CHKSM_GEAR_INFO = Xor COUNTER, GEAR_INFO
*:: CHKSM_GEAR_INFO = Negate CHKSM_GEAR_INFO
*:: CHKSM_GEAR_INFO = And CHKSM_GEAR_INFO , 0x0F
*:: CHKSM_GEAR_INFO = Lsh CHKSM_GEAR_INFO , 4
*:: CHKSM_GEAR_INFO = Or CHKSM_GEAR_INFO , GEAR_INFO
*: COUNTER is incremented every time after the CAN message has been sent
*'''Byte 4''' - LNG_ACC
*: Longitudial Acceleration
*: Calculation: (HEX / 10) - 12.7m/s²
*: Min: -12.7m/s²
*: Max: 12.7m/s²
*'''Byte 5 - Bitfield'''
**'''Bit 0 - L_GS [0]'''
**'''Bit 1 - L_GS [1]'''
**: SMG Error State
**: 0 = No Error
**: 3 = Error Active (Gear Of Death)
**'''Bit 2 - Unused (Always 1)'''
**'''Bit 3 - TC_ACT'''
**: Traction Control Intervention
**: 0 = no
**: 1 = yes
**'''Bit 4 - Unused'''
**'''Bit 5 - GONG'''
**'''Bit 6 - DT_REINF [0]'''
**'''Bit 7 - DT_REINF [1]'''
*'''Byte 6 - DT_REINF [2-9]'''
*: Torque Factor On Wheels
*: Calculation = HEX / 2.56
*: TQ_CLU / TQ_ENG * SMG_I_HA * SMG_I_GEAR / SMG_R_RAD_DYN
*'''Byte 7 - TQ_CLU'''
*: Torque On Clutch
=Instrument Cluster=
==ICL2 0x613==
Refresh Rate: 200ms
*'''Byte 0''' - KM_CTR_CAN - Odometer LSB
*'''Byte 1''' - KM_CTR_CAN - Odometer MSB
*'''Byte 2''' - FTL_CAN - Fuel Tank Level (Bits 0-6)
**'''Bit 7''' - FTL_RES_CAN - Fuel Tank Level Reserve Switch
*'''Byte 3''' - T_REL_CAN - Running Clock LSB
*'''Byte 4''' - T_REL_CAN - Running Clock MSB
*'''Byte 5''' - FTL_CAN_L - Fuel Tank Level Driver Side (Bits 0-5)
**'''Bit 6''' - Unused
**'''Bit 6''' - Unused
**'''Bit 7''' - Unused
**'''Bit 7''' - Unused
*'''Byte 6''' - Unused
*'''Byte 6''' - Oil Level (MSS54HP only)
*'''Byte 7''' - Unused
*'''Byte 7''' - Unused
==ICL3 0x615==
Refresh Rate: 200ms
*'''Byte 0 - Bitfield'''
**'''Bit 0''' - TQ_ACCIN_CAN - Torque Offset For Air Conditioning Compressor (Bit 0)
**'''Bit 1''' - TQ_ACCIN_CAN - Torque Offset For Air Conditioning Compressor (Bit 1)
**'''Bit 2''' - TQ_ACCIN_CAN - Torque Offset For Air Conditioning Compressor (Bit 2)
**'''Bit 3''' - TQ_ACCIN_CAN - Torque Offset For Air Conditioning Compressor (Bit 3)
**'''Bit 4''' - TQ_ACCIN_CAN - Torque Offset For Air Conditioning Compressor (Bit 4)
**'''Bit 5''' - LV_REQ_TCO_L - Request For Lowest Cooling Temp (c_tco_bol_ect)
**'''Bit 6''' - LV_ACCIN - Air Conditioning Compressor Status (0=off, 1=on)
**'''Bit 7''' - LV_ACIN - Air Conditioning Request
*'''Byte 1 - Bitfield'''
**'''Bit 0''' - LV_REQ_HEAT - Increased Heat Request
**'''Bit 1''' - LV_TOW - Trailer Operation Mode
**'''Bit 2''' - LV_LGT - Day / Night Lighting
**'''Bit 3''' - LV_HS - Hood Switch
**'''Bit 4''' - N_ECF - Electric Cooling Fan Level (Bit 0)
**'''Bit 5''' - N_ECF - Electric Cooling Fan Level (Bit 1)
**'''Bit 6''' - N_ECF - Electric Cooling Fan Level (Bit 2)
**'''Bit 7''' - N_ECF - Electric Cooling Fan Level (Bit 3)
*'''Byte 2''' -
*'''Byte 3''' - TAM_CAN - Ambient Temperature
*'''Byte 4 - Bitfield'''
**'''Bit 0''' - LV_DOOR - Door Switch
**'''Bit 1''' - LV_HBR - Hand Brake Switch
**'''Bit 2''' -
**'''Bit 3''' -
**'''Bit 4''' -
**'''Bit 5''' - LV_REQ_TCO_L -
**'''Bit 6''' - LV_ACCIN - Air Conditioning Compressor Status (0=off, 1=on)
**'''Bit 7''' - LV_ACIN - Air Conditioning Request
*'''Byte 5''' -
*'''Byte 6''' -
*'''Byte 7''' -

Revision as of 11:24, 23 April 2021

CAN Bus on BMWs E46 chassis operates at a speed of 500kb/s and so does the MS43 ECU.

There is a total of 15 message boxes, that can be configured to be received or send by the C167 processor.

The messages are ordered by the CAN registers name inside the CPU beginning with 1 and ending with F. Unused boxes are not listed here.


Siemens MS43 reads the following messages for operation, if the corresponding module is present in car:


Siemens MS43 sends the following messages:


Visualised in Tuner Pro the CAN configuration table looks like this:

Tuner Pro MS43 CAN Init.png


In addition to that, there are several messages that are not used by the ECU, but still present on the CAN Bus:


DME1 0x316

Refresh Rate: 10ms

  • Byte 0 - Bitfield
    • Bit 0 - LV_SWI_IGK
      Ignition Key Voltage State
      0 = terminal 15 off detected
      1 = terminal 15 on detected
    • Bit 1 - LV_F_N_ENG
      Crankshaft Sensor State
      0 = no CRK error present
      1 = CRK error present
    • Bit 2 - LV_ACK_TCS
      Traction Control State
      0 = either ASC1 was not received within the last 500 ms or it contains a plausibility error
      1 = the ASC message ASC1 was received within the last 500 ms and contains no plausibility errors of the requirements TQI_ASR_CAN / TQI_MSR_CAN
    • Bit 3 - LV_ERR_GC
      Gear Change Error State
      0 = gear change not or partly possible
      1 = gear change possible
    • Bit 4 - SF_TQD [0]
    • Bit 5 - SF_TQD [0]
      Charge Intervention State
      0 = the required intervention can be performed completely or if there is no ASC requirement.
      1 = the required intervention cannot be performed completely because the IGA retard limit is reached.
      2 = the required intervention cannot be performed completely because the charge actuators are fully closed (this case is not possible with MTC without break-away mechanism)
      3 = "limited vehicle dynamics" is active (MTC/ISA error)
    • Bit 6 - Unused
    • Bit 7 - LV_F_SUB_TQI
      MAF Error State
      0 = MAF ok
      1 = MAF error present
  • Byte 1 - TQI_TQR_CAN
    Indexed Engine Torque in % of C_TQ_STND (including ASR/MSR/ETCU/LIM/AMT/GEAR intervention)
  • Byte 2 - N_ENG [LSB]
  • Byte 3 - N_ENG [MSB]
    Engine Speed in rpm
    Calculation = HEX[MSB] * 256 + HEX[LSB]
  • Byte 4 - TQI_CAN
    Indicated Engine Torque in % of C_TQ_STND (based on PVS, N, AMP, TIA ,TCO, IGA, PUC)
  • Byte 5 - TQ_LOSS_CAN
    Engine Torque Loss (due to engine friction, AC compressor and electrical power consumption) in % of C_TQ_STND
  • Byte 6 - TQI_MAF_CAN
    Theorethical Engine Torque in % of C_TQ_STND after charge intervention (based on MAF, IGA)
  • Byte 7 - Bitfield
    • Bit 0 - ERR_AMT_CAN
    • Bit 1 - ERR_AMT_CAN


DME2 0x329

Refresh Rate: 10ms

  • Byte 0 - Multiplexed Information
    • Bit 0 - MUX_INFO [0]
    • Bit 1 - MUX_INFO [1]
    • Bit 2 - MUX_INFO [2]
    • Bit 3 - MUX_INFO [3]
    • Bit 4 - MUX_INFO [4]
    • Bit 5 - MUX_INFO [5]
      CAN_LEVEL = CAN bus function level. This is always 0x11 for MS43
      OBD_STEUER = STATE_DIAG_GS (Status of GS diagnosis for feedback to gearbox)
      MD_NORM = Refactored C_TQ_STND from 0x3FF (0-1023Nm) to 0x3F (0-1008Nm) with decreased resolution of 16Nm
    • Bit 6 - MUX_CODE [0]
    • Bit 7 - MUX_CODE [1]
      0 = CAN_LEVEL
      2 = OBD_STEUER
      3 = MD_NORM
  • Byte 1 - TEMP_ENG
    Engine (Coolant) Temperature in °C
    Calculation = (HEX * 0.75) - 48°C
    Init: 0xFF
    Min: 0x01 (-48°C)
    Max: 0xFF (142.5°C)
  • Byte 2 - AMP_CAN
    Ambient Pressure in hPa
    Calculation = (HEX * 2) + 598hPa
    Init = 0x00
    Min = 0x01 (600hPa)
    Max = 0xFE (1106hPa)
    Error = 0xFF
  • Byte 3 - Bitfield
    • Bit 0 - LV_SWI_CLU
      Clutch Switch State
      0 = released
      1 = depressed
    • Bit 1 - LV_LEVEL_IS
      Idle Regulator State
      0 = idle above threshold
      1 = idle below threshold
    • Bit 2 - LV_ACK_CRU_AD_ECU
      Acknowledge of ACC1 CAN Message
      0 = nACK
      1 = ACK
    • Bit 3 - LV_ERU_CAN
      Engine Running State
      0 = engine stopped
      1 = engine running
    • Bit 4 - (STATE_CRU_CAN)???
    • Bit 5 - STATE_MSW_CAN [0]
    • Bit 6 - STATE_MSW_CAN [1]
    • Bit 7 - STATE_MSW_CAN [2]
      0 = No Button Pressed (Init Value)
      1 = Set / Acceleration (tip-up)
      2 = Deceleration (tip-down)
      3 = Resume
      4 = Deactivate (I/O)
      7 = Error Condition
  • Byte 4 - TPS_VIRT_CRU_CAN
  • Byte 5 - TPS_CAN
    Accelerator Pedal Position in % of PVS_MAX
    Calculation = HEX / 2.56
    Init = 0x00
    Min = 0x01 (0%)
    Max = 0xFE (99.2%)
    PVS Error = 0xFF
  • Byte 6 - Bitfield
    • Bit 0 - LV_BS
      Brake Switch State
      0 = brake not actuated
      1 = brake actuated
    • Bit 1 - LV_ERR_BS
      Brake Switch System State
      0 = brake switch system OK
      1 = brake switch system faulty
    • Bit 2 - LV_KD_CAN
      Kick Down State
      0 = kick down not active
      1 = kick down active
    • Bit 3 - STATE_CRU_CAN [0]
    • Bit 4 - STATE_CRU_CAN [1]
    • Bit 5 - STATE_CRU_CAN [2]
      0 = LV_CRU_ACT = 0
      1 = LV_CRU_ACT = 1, constant drive (or tip-up / tip-down)
      3 = LV_CRU_ACT = 1, resume
      5 = LV_CRU_ACT = 1, set / acceleration
      7 = LV_CRU_ACT = 1, deceleration
    • Bit 6 - REQ_SHIFTLOCK [0]
    • Bit 7 - REQ_SHIFTLOCK [1]
      0 = no actuation is active
      3 = actuation ISA, MTC or N_SP_IS is active
  • Byte 7 - Unused


DME3 0x338

Refresh Rate: 1000ms and at signal change

  • Byte 0 - Unused
  • Byte 1 - Unused
  • Byte 2 - STATE_SOF_CAN
    Sport Button Status
    0 = Sport Button On (requested by SMG)
    1 = Sport Button Off
    2 = Sport Button On
    3 = Sport Button Error
    Init: 0x01
  • Byte 3 - Unused
  • Byte 4 - Unused
  • Byte 5 - Unused
  • Byte 6 - Unused
  • Byte 7 - Unused

DME4 0x545

Refresh Rate: 10ms

  • Byte 0 - Bitfield
    • Bit 0 - Unused
    • Bit 1 - LV_MIL - Check Engine Light
    • Bit 2 - Unused
    • Bit 3 - LV_MAIN_SWI_CRU - CRU_MAIN_SWI
    • Bit 4 - LV_ETC_DIAG - EML Light
    • Bit 5 - Unused
    • Bit 6 - LV_FUC_CAN - Fuel Tank Cap Light
    • Bit 7 - Unused
  • Byte 1 - FCO[LSB]
  • Byte 2 - FCO[MSB]
    Fuel Consumption
  • Byte 3 - Bitfield
    • Bit 0 - Oil Level Error LED M5 Cluster
    • Bit 1 - Oil Level Warning LED Every Other Cluster
    • Bit 2 - Oil Level Error LED M5 Cluster
    • Bit 3 - LV_TEMP_ENG - Coolant Overheating Light
    • Bit 4 - M-Cluster Warm-Up LEDs
    • Bit 5 - M-Cluster Warm-Up LEDs
    • Bit 6 - M-Cluster Warm-Up LEDs
    • Bit 7 - Unused
  • Byte 4 - TOIL_CAN
    Oil Temperature
  • Byte 5 - Bitfield
    • Bit 0 - Battery Chargelight (Alpina Roadster Only)
    • Bit 1 - Unused
    • Bit 2 - Unused
    • Bit 3 - Unused
    • Bit 4 - Unused
    • Bit 5 - Unused
    • Bit 6 - Unused
    • Bit 7 - Unused
  • Byte 6 - Oil Level (MSS54HP only)
  • Byte 7 - Unused