Advertising:
Siemens MS43 Old Stuff: Difference between revisions
From MS4X Wiki
(Created page with "asdf") |
No edit summary |
||
Line 1: | Line 1: | ||
=Launch Control= | |||
[[File:Old_Tunerpro_lc_config.jpg|thumbnail|right|TunerPro launch control maps]] | |||
'''Setting up LC:''' | |||
Set the following maps in TunerPro: | |||
Configuration Launch Control | |||
*Launch_PVS_min (i suggest to set this switch over 50% and UNDER 70%. Anything different may lead to non-working LC) | |||
*Launch_TCO_min (and this to "-48" ) | |||
*Launch_RPM_max | |||
*Launch_VS_max (set to "1") | |||
'''Using LC:''' | |||
# Make sure coolant temp is equal or above the threshold and ASC/DSC is turned off | |||
# Depress the clutch pedal | |||
# Put car into first gear | |||
# Floor the accelerator pedal! (At least that °PVS matches the threshold!) | |||
# Engine speed should bounce at chosen rpm setpoint. There may be offset which engine speed bounces, like +/- 200rpm | |||
# Release clutch pedal while holding accelerator pedal down. | |||
# Engine speed will be reduced until vehicle speed exceeds chosen threshold (currently not working!) | |||
Engine RPM setting may be adjusted according to road conditions/tire setup, in order to minimize wheel spin. | |||
For additional aggressiveness set "c_n_max_hys_max" to 32 or 64, then LC is much less bouncy | |||
'''Example video:''' | |||
<youtube>CZDCd-bMDyo</youtube> | |||
'''Alternative for non working LC''' | |||
[[File:LC_fix_Brakeswitch.jpg|800px]] | |||
=Map reduction "fewmaps"= | |||
The _fewmaps file reduces the number of used maps to the following ones: | |||
*Injection | |||
**Idlespeed: ip_ti_tco_1_is_ivvt__n__maf | |||
**Part load: ip_tib__n__maf | |||
**Full load: | |||
*Ignition | |||
**Idlespeed: ip_igab_is__n__maf | |||
**Part- & full loadip_igab__n__maf | |||
*VANOS | |||
**Idle speed: IP_CAM_SP_tco_1_IN_IS / IP_CAM_SP_tco_1_EX_IS | |||
**Part load: IP_CAM_SP_tco_1_IN_PL / IP_CAM_SP_tco_1_EX_PL | |||
**Full load: IP_CAM_SP_tco_1_IN_FL / IP_CAM_SP_tco_1_EX_FL | |||
This is great for finding basemaps. |
Latest revision as of 16:25, 31 March 2020
Launch Control
Setting up LC:
Set the following maps in TunerPro:
Configuration Launch Control
- Launch_PVS_min (i suggest to set this switch over 50% and UNDER 70%. Anything different may lead to non-working LC)
- Launch_TCO_min (and this to "-48" )
- Launch_RPM_max
- Launch_VS_max (set to "1")
Using LC:
- Make sure coolant temp is equal or above the threshold and ASC/DSC is turned off
- Depress the clutch pedal
- Put car into first gear
- Floor the accelerator pedal! (At least that °PVS matches the threshold!)
- Engine speed should bounce at chosen rpm setpoint. There may be offset which engine speed bounces, like +/- 200rpm
- Release clutch pedal while holding accelerator pedal down.
- Engine speed will be reduced until vehicle speed exceeds chosen threshold (currently not working!)
Engine RPM setting may be adjusted according to road conditions/tire setup, in order to minimize wheel spin.
For additional aggressiveness set "c_n_max_hys_max" to 32 or 64, then LC is much less bouncy
Example video:
Alternative for non working LC
Map reduction "fewmaps"
The _fewmaps file reduces the number of used maps to the following ones:
- Injection
- Idlespeed: ip_ti_tco_1_is_ivvt__n__maf
- Part load: ip_tib__n__maf
- Full load:
- Ignition
- Idlespeed: ip_igab_is__n__maf
- Part- & full loadip_igab__n__maf
- VANOS
- Idle speed: IP_CAM_SP_tco_1_IN_IS / IP_CAM_SP_tco_1_EX_IS
- Part load: IP_CAM_SP_tco_1_IN_PL / IP_CAM_SP_tco_1_EX_PL
- Full load: IP_CAM_SP_tco_1_IN_FL / IP_CAM_SP_tco_1_EX_FL
This is great for finding basemaps.